RF Power Meter 27 - 2400 5800 mhz arduino ad8319 5.8Ghz 2.4Ghz antenna tool FPV

Description

RF Power Meter 27 144 433 868 91
RF Power Meter 27 144 433 868 915 1200 2400 5800 mhz open source Arduino ad8319 (AD8317 series)
This not only RF Power meter.
You can also find any RF Source by using Geiger counter sound effect by internal Buzzer And trim you antennas in raw mode.
New Review on Russian
https://www.youtube.com/watch?v=g9lK-eB-P6E
Full Review on Russian
https://youtu.be/RTmjluC_rRM
Review on Polish
https://www.youtube.com/watch?v=YcqwKd8l8Y4
Arduino Source Code
http://www.expertrc.com/power-meter/
3D Print Case
http://www.thingiverse.com/thing:2123330
UP. Use as satellite finder (in
Find MODE
with proper sma to f adapter and small modification)
https://www.youtube.com/watch?v=RJ60qIfYWzM
Specs:
OLED Display
Frequency range: 1MHz thru 8-10GHz, calibrated on 27 144 433 868 915 1200 2400 5800 mhz
Power level without attenuator: -50dBm thru 0dBm (best -10..-40)
Power level with 30dBm attenuator: up to +30dBm (1W, 1000mW)
Power level with 30dBm+10dBm attenuator:
up to +40dBm (10W,
a few
seconds only)
Adjustments: Programmable attenuator setting
Power: micro USB, or DC power source, 4.2V-13V
Reverse power protected
Power Consumption: 100mA
Calibrated by 2 points per band EACH UNIT!
(you can change calibration in call menu)
Readout in mW, or dBm or the same
Connector: SMA F
Measure
MM - Maximum Mode (recommended)
CM - Continuous Mode
AM - Average Mode
Find MODE
Press UP button and power on
press ENT to set Flor
RAW MODE
Press DOWN button and power on
FILL MODE
Press ENT button and power on
Lot include
-Power meter with v25 firmware
-30dB SMA Attenuator
-SMA-M to SMA-M pigtail cable
-SMA-F to RP-SMA adapter (regular use in 2.4 and 5.8Ghz band)
-Box
!WARNING!
Never CONNECT POWER MORE THEN 1mW
direct
to input!
Calibration menu
Press Down button and UP Button AND power on
Open terminal windows at 57600, press enter.
backup all first!
Device is already factory calibrated!
You do this At Your Own Risk!
Yes it is open source,
you can flash any you want, but not use EEPROM in Arduino, else you can lost factory calibration data.
It is hard to measure very accurate on 1GHz band and up-
very sensitive to clean connector, cable tight, hand orientation, temperature and over.
It is hobby stuff, not 10k$ lab)
Changing environmental conditions also make it hard to measure.
Factory calibrate only device, for better results please know - pigtail have up to ~0.6dBm and RP-SMA adapter have up to 0.8dBm
attenuation a special
for >2Ghz band.
We have two version of attenuator:
gold and silver.
Quality the same, both 30dBm.
So, we ship random model.
Please note:
We ship orders once a week, regular on Wednesdays.
We have small batch every 2-3 weeks.
Flat Shipping Rate Per Order - 4.99$
Combine to save $$$.
Уважаемые Россияне! К сожалению из за кое сами знаете кого вы не сможете оплатить этот лот в долларах, а я выставить в рублях, т.ч. купите в другом месте, гугл в помощь.